{"id":5776,"date":"2022-08-12T06:43:21","date_gmt":"2022-08-11T20:43:21","guid":{"rendered":"http:\/\/otcm.wordpress.com\/2022\/08\/11\/staying-alive\/"},"modified":"2022-08-12T06:43:21","modified_gmt":"2022-08-11T20:43:21","slug":"staying-alive","status":"publish","type":"post","link":"https:\/\/www.vibewire.com.au\/?p=5776","title":{"rendered":"Staying Alive\u2026."},"content":{"rendered":"

Firstly, I\u2019m sure you\u2019ll all enjoy the Beegees fuelled ear worm this post title has created\u2026. Yeah, sorry about that.<\/p>\n

A couple of years ago (I might be being kind to myself here, it\u2019s probably more like 5) I picked up a couple of the then new Hornby 0-4-0 Sentinel shunters and repainted them to fit in with the rest of my British Steel fleet. Following a weathering session I was very pleased with how these came out.<\/p>\n

<\/figure>\n

I fitted the standard Hornby chips to these and they ran fine on the workbench. Unfortunately, the same couldn\u2019t be said when I put them on the layout. For some reason, even though I keep the railhead clean, the weathering powder used in preparing the trackbed and blending it in did not suit a very short wheelbase 0-4-0!<\/p>\n

I\u2019m currently working through my collection of industrial locos and upgrading them with better quality chips, as well as fitting stay alives – the difference being remarkable. As part of this project I thought I\u2019d dig the Sentinels out the \u2018don\u2019t know what to do with them\u2019 draw and see if a stay alive could be squeezed in – below is how I did it!<\/p>\n

<\/figure>\n

First up, remove the cab and the long bonnet module so we can see the insides – this is going to be a squeeze so the Hornby 4 pin connector also needs to go – with this snipped off, trim the motor and pickup wires to a sensible length and strip the ends.<\/p>\n

<\/figure>\n

Next up, we need to make some space in the moulded cab interior to fit everything. Here I\u2019ve hacked open a much wider slot than originally existed. The handbrake wheel is also sacrificed in the name of reliable running.<\/p>\n

<\/figure>\n

With space created, it\u2019s time to deploy the new kit\u2026 a DCC Concepts Zen Micro 8 pin chip with the plug cut off and the wires cut back is perfect for the job here. This is coupled to a decent size Lais DCC stay alive (budgets and all that). Remember to pop some heat shrink around all the soldered joints!<\/p>\n

<\/figure>\n

There is just enough space within the short bonnet and under the cab floor to squeeze the stay alive and decoder sat next to each other. The wiring can then be tucked into the space previously occupied by the Hornby 4 pin plug. (yes I know the masking job I did on the motor when respraying the chassis is a bit \u2018rudimentary\u2019)<\/p>\n

<\/figure>\n

Finally, the cab floor can be clipped back into place and the loco put back together.<\/p>\n

Fitting the new decoders and the stay alives has completely transformed the locos, and they are now smooth runners even over my dodgy (weathering powder covered) trackwork. As such they will be making an appearance at future shows\u2026. All in all a successful side project!<\/p>\n

Chris<\/p>\n","protected":false},"excerpt":{"rendered":"

Firstly, I\u2019m sure you\u2019ll all enjoy the Beegees fuelled ear worm this post title has created\u2026. Yeah, sorry about that. A couple of years ago (I might be being kind to myself here, it\u2019s probably more like 5) I picked up a couple of the then new Hornby 0-4-0 Sentinel shunters and repainted them to \u2026 <\/p>\n

Continue reading “Staying Alive\u2026.”<\/span><\/a><\/p>\n","protected":false},"author":20,"featured_media":4845,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"om_disable_all_campaigns":false,"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"_uf_show_specific_survey":0,"_uf_disable_surveys":false,"footnotes":""},"categories":[],"tags":[],"class_list":["post-5776","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry"],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=\/wp\/v2\/posts\/5776","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=\/wp\/v2\/users\/20"}],"replies":[{"embeddable":true,"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=5776"}],"version-history":[{"count":5,"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=\/wp\/v2\/posts\/5776\/revisions"}],"predecessor-version":[{"id":376232,"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=\/wp\/v2\/posts\/5776\/revisions\/376232"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=\/wp\/v2\/posts\/4845"}],"wp:attachment":[{"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=5776"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=5776"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.vibewire.com.au\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=5776"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}